Posted on

organo clay modified bentonite CP-34

organo clay modified bentonite

Organo clay modified bentonite CP-34

CP-34 is an organo clay (modified bentonite), designed especially for use  in solvent based system. It can be used widely in solvents from low polarity to medium-high polarity.

Organoclays is mainly used in paints and coatings, oilfield drilling and fracturing fluids, grease adhesives, cosmetics and other fields. Organophilic clay is mainly used as a thickener, suspending agent, rheology additive, and thixotropic agent. It has outstanding performance in anti-settling and anti-sag properties.

Properties | Organo clay modified bentonite

Composition                      Organic derivative of a montmorillonite clay

Appearance                       Fine powder, light yellow

Moisture content (105℃,2hr)         ≤3.5%

Loss on ignition (1000℃)            28%-30%

Bulk density                       0.53g/cm3

Fineness (<74μm, %)               ≥98%

Advantages | Organo clay modified bentonite

High gelling efficiency

Light color gel

Produce reproducible thixotropic consistency over a wide temperature range

Imparts particle suspension, preventing hard settling of pigment and fillers.

Exerts strong film reinforcing action in organic binder systems.

Application

CP-34 is used in the following applications:

Marine paint, Industrial paint, heavy-duty, anticorrosion paint such as bituminous coatings, polyester paints, Alkyd paints.

Sealant

Inks

Grease

Unsaturated polyester putty

Using

CP-34 disperses under high shear and requires a polar activator for best efficiency. Heat is not required to obtain good dispersion. Addition levels are typically in 0.2%~2.0%. Polar activator (95% Ethanol or 95% Methanol) is needed. Normally addition level of polar activator is recommended to be 40%~50% of CP-34 in weight. If in xylene system, addition level of polar activator is about 30%-40% of CP-34 in weight.

Pre-gel is made as below procedure.

Charge solvent to mill

Slowly add CP-34(6-10% by weight of total pregel) to mill under agitation.

Mix at high speed for 5 minutes.

Add polar activator.

Mix at high speed for 5 minutes.

Package

Kraft paper bag with PE liner or multi-wall paper sacks or customized. 25kg/bag or 22.68kg/bag or customized

Ask A Quote
Posted on

organo clay (modified montmorillonite)CP-27

organo clay (modified montmorillonite)

organo clay (modified montmorillonite)

organo clay (modified montmorillonite)CP-27 is an organo clay (modified montmorillonite), designed especially for use in solvent based system. It is used especially in solvents of high polarity.

Properties | organo clay (modified montmorillonite)

Composition                      Organic derivative of a montmorillonite clay

Appearance                       Fine powder, light yellow

Moisture content (105℃,2hr)         ≤3.5%

Loss on ignition (1000℃)            34.7%

Bulk density                       0.53g/cm3

Fineness (<74μm, %)               ≥98%

Advantages | organo clay (modified montmorillonite)

  • High gelling efficiency
  • Produce reproducible thixotropic consistency over a wide temperature range
  • Imparts particle suspension, preventing hard settling of pigment and fillers
  • Exerts strong film reinforcing action in organic binder systems

Application

CP-27 is used in the following applications:

  • Marine paint, Industrial paint, heavy-duty, anticorrosion paint (especially forepoxy paint)
  • Grease
  • Ink
  • Sealant
  • Unsaturated polyester putty

Using

CP-27 disperses under high shear and requires a polar activator for best efficiency. Heat is not required to obtain good dispersion. Addition levels are typically in 0.2%~2.0%. Normally addition level of polar activator (95% Ethanol or 95% Methanol) is recommended to be 45%~60% of CP-27 in weight.

Package

Kraft paper bag with PE liner or multi-wall paper sacks or customized. 25kg/bag or 22.68kg/bag or customized

We sincerely welcome you to inquire about our ORGANOCLAY products or request samples. Our samples are free and we provide you with a one-stop application solution.

You will need a lot of guidance and service during your use, and our technical department will provide you with a series of services.

The application of organic bentonite in oilfield drilling paints, coatings, inks, and lubricants has been widely welcomed and accepted in the market.

Looking forward to your inquiry.

Posted on

organo clay rheological additive CP-EZ

Organo clay rheological additive

organo clay rheological additive CP-EZ

Organo clay rheological additive CP-EZ is a kind of organo clay rheological additive.Especially organoclays is recommended to be applied in medium polarity and high polarity system including aromatic and aliphatic solvent. If you are producing paints, coatings, drilling fluids, inks, greases, sealants, and cosmetics, then our organic bentonite clay is undoubtedly your best choice for thickening rheology modifier.

Properties | organo clay rheological additive CP-EZ

Composition                      Organic derivative of a montmorillonite clay Appearance                       Fine powder, light yellow Moisture content (105℃,2hr)         ≤3.5% Loss on ignition (1000℃)            35%-37% Bulk density                       0.40~0.60g/cm3 Fineness (<74μm, %)               ≥99% Dispersion fineness (μm)            ≤10

Advantages | organo clay rheological additive CP-EZ

  • Easy dispersing, fine particle size
  • High purity and low silica content
  • High viscosity and thixotropy
  • Eliminate polar activator in medium and high polarity solvent
  • Wide application range. It can be applied in almost all resins and solvents
Application CP-EZ is used in the following applications:
  • Paints including decorative paint, industrial paint
  • Grease
  • Inks
  • Oil drilling mud
  • Cleaning agent
  • Oil putty
Using CP-EZ can be added directly in powder under high shear condition. The addition is recommended to be before grinding procedure to get the best effectiveness. Addition level is commonly 0.2%~1.0%. In low polarity system such as mineral spirit, if polar activator is added, better efficiency can be achieved. Dosage of polar activator is suggested to be 10%-20% of CP-EZ by weigh    
Ask A Quote
Posted on

organoclay (tetraallkyl ammonium bentonite) CP-250A

organo clay (modified montmorillonite)

Organoclay (tetraallkyl ammonium bentonite) CP-250A

Organoclay (tetraallkyl ammonium bentonite) CP-250A is a kind of purified and modified organoclay rheological additive, designed especially for use in Grease based on synthetic oils such as vegetable oil, polyester oil.

Organo bentonite has high gelling efficiency, fine thixotropy and perfect anti-settling.

what is bentonite grease
what is bentonite grease

Properties   | Organo clays tetraallkyl ammonium bentonite

Composition                      Organic derivative of a montmorillonite clay

Appearance                       Fine powder, light yellow

Moisture content (105℃,2hr)         ≤3.5%

Loss on ignition (1000℃)            34%-36%

Bulk density                       0.42g/cm3

Fineness (<74μm, %)               ≥98%

Advantages | Organoclay tetraallkyl ammonium bentonite

High efficiency

The gel is of light colour and high clarity

Easy to use, no need to pregel

Eliminate polar activator

Consistent development of rheology

Can be used to post correct

Application | Organoclay tetraallkyl ammonium bentonite

OrganoBentonite grease CP-250A is used in the following applications:

Grease Lubricant(the base oil is synthetic oil such as middle-high viscosity petroleum, mineral oil, diester oil, polyester oil, vegetable oil etc.)

Wood coating 

Using of bentonite grease

When rheology modifier is used in Grease Lubricant, polar activator is needed. Polar activator is acetone/water(95/5). The dosage of activator is 20%-30% of the weight of CP-250A. And also high shear can promote the dispersing of CP-250A.

Adding procedure as follows:

If condition permits, heat the base oil to 60~70℃

Add organophilic clay CP-250A while stirring, addition level is 7%-10% of the total formulation. Stir  5~10minutes

Add polar activator, addition level is 2%-3% of the total formulation. Then add other additives, stir 25~30minutes.

Use pump to help it pass colloid grinding and homogenizer.

Deair, filtrate, pack.Note: With High-speed dispersant of grinding machine, and properly prolong the dispersing time, better gelatin performance can be reached.

The Lubricanting grease which uses organoclay as thickener will own high dropping point, thus can be used under high temperature and presents good impermeability and water resistance.

Package | Organoclay tetraallkyl ammonium bentonite

Kraft paper bag with PE liner or multi-wall paper sacks or customized. 25kg/bag or 22.68kg/bag or customized

Storage

organic clay Bentonite grease has a shelf life of 2 years, and should be stored in ventilated cool and dry place.

Notice

The information on use is based on data which are believed reliable, but any recommendation or suggestion made are without guarantee or warranty, since the conditions of use are outside our control.

All bentonite grease | Organoclay tetraallkyl ammonium bentonite are sold on the conditions that purchasers shall make their own tests to determine the suitability of such products for their purpose and that all risks are assumed by user.

We disclaim any responsibility for damages resulting from careless or improper handling or use. Nothing herein is to be taken as permission, inducement or recommendation to practice any patented invention without a license.

[email protected]

Cell (Whatsapp):    +86-13185071071

what is bentonite grease, above info is a part of answer for this question.

Organoclay tetraallkyl ammonium bentonite

 
 
 
 
Ask A Quote
Posted on

rheology modifier (rheological additive) CP-10A

organo clay (modified montmorillonite)

Rheology modifier (rheological additive) CP-10A is a kind of organo clay rheological additive. It is used in systems of non-polar to medium polarity aliphatic and other solvents (ketones, ester, ether esters, alcohols, aromatic)

Properties

Composition                      Organic derivative of a montmorillonite clay

Appearance                       Fine powder,white

Moisture content (105℃,2hr)         ≤3.5%

Loss on ignition (1000℃)            30%-34%

Bulk density                       0.35~0.45g/cm3

Fineness (<74μm, %)               ≥98%

Dispersion fineness (μm)            ≤40

Advantages

  • High efficiency
  • The gel is of light colour and high clarity
  • Easy to use, no need to pregel
  • Eliminate polar activator
  • Consistent development of rheology
  • Can be used to post correct

Application

CP-10A is used in the following applications:

  • Paints
  • Sealants &adhesives
  • Inks
  • Cosmetic
  • Nano-composite

Using

CP-10A can be added directly in powder without polar activator and making pre-gel. But better performance may achieve if polar activator is added and pre-gel procedure is affected.

The addition is recommended to be before grinding procedure to get the best effectiveness. Addition level is commonly 0.2%~1.0%.

Posted on

Organic clay (Solvent based organoclay) CP-10

organo clay (modified montmorillonite)

Organic Clay | Your Best Organoclay Rheological Additive

Organic clay (Solvent based organoclay) CP-10 is a kind of organo clay rheological additive. It is used in systems of non-polar to medium polarity aliphatic and other solvents (ketones, ester, ether esters, alcohols, aromatic).

Properties

Composition                      Organic derivative of a montmorillonite clay

Appearance                       Fine powder,white

Moisture content (105℃,2hr)         ≤3.5%

Loss on ignition (1000℃)            30%-34%

Bulk density                       0.35~0.45g/cm3

Fineness (<74μm, %)               ≥98%

Dispersion fineness (μm)            ≤40

Advantages

  • High efficiency
  • The gel is of light colour and high clarity
  • Easy to use, no need to pregel
  • Eliminate polar activator
  • Consistent development of rheology
  • Can be used to post correct

Application

Organic clay CP-10 is used in the following applications:

  • Paints
  • Sealants &adhesives
  • Inks
  • Cosmetic
  • Nano-composite

Using

Organic clay CP-10 can be added directly in powder without polar activator and making pre-gel. But better performance may achieve if polar activator is added and pre-gel procedure is affected.

The addition is recommended to be before grinding procedure to get the best effectiveness. Addition level is commonly 0.2%~1.0%.

Package

Kraft bag or kraft complex interior with PE or customized

Ask A Quote
Organic clay
Ask A Quote

Organic Clay | Organic Clay Powder For Paints & Coatings

 If you are looking for a thickener for your grease production, ink production or paint production, then the new organic bentonite produced by Camp Shinning can undoubtedly solve your need for rheological properties.

It has very stable properties in application, especially its rheological properties and thixotropic properties.

Of course, in many applications, we recommend users to add a certain amount of activator to help fully reflect the dispersion and performance of organic bentonite in the whole formula.

The commonly used activators include methanol, ethanol propylene carbonate, and some customers use water as its activator, which also has good performance.

Generally, we recommend that the amount of organic bentonite added to grease or ink should be between 2% and 5%, and we recommend that you determine the amount of organic bentonite according to your own experimental results.

Our packaging is 25kg/bag, or 50lb/bag, which depends on the customer’s requirements. We will determine the amount of packaging.

Finally, most of our bags are made of white valve bags, which have moisture-proof function. Its shelf life is generally about two years. Of course, we recommend that you put them in a dry and ventilated place.

In order to ensure the perfect display of thixotropy, rheology and anti-settlement properties, we propose to place the goods in a dry and ventilated environment to ensure that all properties can be fully displayed.

Of course, there will be some slight differences in use according to different formulations. We recommend that you verify all of these through experiments.

Finally, we would like to inform you that if you encounter any questions when using organobentonite, or if your customers put forward any requirements in the market, you can boldly contact our sales department or technical research and development department.

We can provide product formula adjustment, and we will fully cooperate with your application needs according to your different application fields.

We mentioned above that the water content of our organic bentonite must be less than or equal to 3.5%, and the weight loss on ignition is also between 30 and 34%. Of course, its fineness is more than 98%. This kind of white powdery thickening rheological agent will be your most trusted choice of coating additive and suspending agent in the oil field.

Finally, we would like to say that our organic bentonite is widely sold in the global market, especially in Russia. For example, in the application of oil field drilling and pressure fluid, it is widely welcomed.